wamster/BUT2
1
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
2d9560a691
BUT2/SCR/SCR1.2/TP12/DIR/kern.log

514 lines
47 KiB
Plaintext
Raw Normal View History

update
2023-10-23 13:23:36 +02:00
Sep 25 09:17:11 RP2-13 kernel: imklog 5.8.11, log source = /proc/kmsg started.
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Booting Linux on physical CPU 0xf00
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Initializing cgroup subsys cpu
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Initializing cgroup subsys cpuacct
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Linux version 3.18.11-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.8.3 20140303 (prerelease) (crosstool-NG linaro-1.13.1+bzr2650 - Linaro GCC 2014.03) ) #781 SMP PREEMPT Tue Apr 21 18:07:59 BST 2015
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Machine model: Raspberry Pi 2 Model B
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] cma: Reserved 8 MiB at 0x3a800000
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Memory policy: Data cache writealloc
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] On node 0 totalpages: 241664
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] free_area_init_node: node 0, pgdat 8080f480, node_mem_map ba093000
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Normal zone: 1888 pages used for memmap
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Normal zone: 0 pages reserved
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Normal zone: 241664 pages, LIFO batch:31
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] [bcm2709_smp_init_cpus] enter (8620->f3003010)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] [bcm2709_smp_init_cpus] ncores=4
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] PERCPU: Embedded 10 pages/cpu @ba061000 s11456 r8192 d21312 u40960
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] pcpu-alloc: s11456 r8192 d21312 u40960 alloc=10*4096
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 239776
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2709.boardrev=0xa01041 bcm2709.serial=0x55ad5fb2 smsc95xx.macaddr=B8:27:EB:AD:5F:B2 bcm2708_fb.fbswap=1 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Memory: 940832K/966656K available (5722K kernel code, 397K rwdata, 1748K rodata, 384K init, 763K bss, 25824K reserved)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Virtual kernel memory layout:
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] vmalloc : 0xbb800000 - 0xff000000 (1080 MB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] lowmem : 0x80000000 - 0xbb000000 ( 944 MB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] .text : 0x80008000 - 0x80753a48 (7471 kB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] .init : 0x80754000 - 0x807b4000 ( 384 kB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] .data : 0x807b4000 - 0x808174bc ( 398 kB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] .bss : 0x808174bc - 0x808d6254 ( 764 kB)
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Preemptible hierarchical RCU implementation.
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] NR_IRQS:608
Sep 25 09:17:11 RP2-13 kernel: [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
Sep 25 09:17:11 RP2-13 kernel: [ 0.000014] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
Sep 25 09:17:11 RP2-13 kernel: [ 0.000037] Switching to timer-based delay loop, resolution 52ns
Sep 25 09:17:11 RP2-13 kernel: [ 0.000332] Console: colour dummy device 80x30
Sep 25 09:17:11 RP2-13 kernel: [ 0.001757] console [tty1] enabled
Sep 25 09:17:11 RP2-13 kernel: [ 0.001807] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
Sep 25 09:17:11 RP2-13 kernel: [ 0.001891] pid_max: default: 32768 minimum: 301
Sep 25 09:17:11 RP2-13 kernel: [ 0.002294] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 0.002352] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 0.003633] Initializing cgroup subsys memory
Sep 25 09:17:11 RP2-13 kernel: [ 0.003727] Initializing cgroup subsys devices
Sep 25 09:17:11 RP2-13 kernel: [ 0.003780] Initializing cgroup subsys freezer
Sep 25 09:17:11 RP2-13 kernel: [ 0.003832] Initializing cgroup subsys net_cls
Sep 25 09:17:11 RP2-13 kernel: [ 0.003892] Initializing cgroup subsys blkio
Sep 25 09:17:11 RP2-13 kernel: [ 0.004000] CPU: Testing write buffer coherency: ok
Sep 25 09:17:11 RP2-13 kernel: [ 0.004116] ftrace: allocating 19614 entries in 58 pages
Sep 25 09:17:11 RP2-13 kernel: [ 0.052589] CPU0: update cpu_capacity 1024
Sep 25 09:17:11 RP2-13 kernel: [ 0.052667] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
Sep 25 09:17:11 RP2-13 kernel: [ 0.052706] [bcm2709_smp_prepare_cpus] enter
Sep 25 09:17:11 RP2-13 kernel: [ 0.052859] Setting up static identity map for 0x528478 - 0x5284ac
Sep 25 09:17:11 RP2-13 kernel: [ 0.112518] [bcm2709_boot_secondary] cpu:1 started (0) 17
Sep 25 09:17:11 RP2-13 kernel: [ 0.112829] CPU1: Booted secondary processor
Sep 25 09:17:11 RP2-13 kernel: [ 0.112838] [bcm2709_secondary_init] enter cpu:1
Sep 25 09:17:11 RP2-13 kernel: [ 0.112892] CPU1: update cpu_capacity 1024
Sep 25 09:17:11 RP2-13 kernel: [ 0.112902] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
Sep 25 09:17:11 RP2-13 kernel: [ 0.132488] [bcm2709_boot_secondary] cpu:2 started (0) 17
Sep 25 09:17:11 RP2-13 kernel: [ 0.132746] CPU2: Booted secondary processor
Sep 25 09:17:11 RP2-13 kernel: [ 0.132753] [bcm2709_secondary_init] enter cpu:2
Sep 25 09:17:11 RP2-13 kernel: [ 0.132784] CPU2: update cpu_capacity 1024
Sep 25 09:17:11 RP2-13 kernel: [ 0.132792] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
Sep 25 09:17:11 RP2-13 kernel: [ 0.152558] [bcm2709_boot_secondary] cpu:3 started (0) 18
Sep 25 09:17:11 RP2-13 kernel: [ 0.152795] CPU3: Booted secondary processor
Sep 25 09:17:11 RP2-13 kernel: [ 0.152802] [bcm2709_secondary_init] enter cpu:3
Sep 25 09:17:11 RP2-13 kernel: [ 0.152831] CPU3: update cpu_capacity 1024
Sep 25 09:17:11 RP2-13 kernel: [ 0.152840] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
Sep 25 09:17:11 RP2-13 kernel: [ 0.152933] Brought up 4 CPUs
Sep 25 09:17:11 RP2-13 kernel: [ 0.153054] SMP: Total of 4 processors activated (153.60 BogoMIPS).
Sep 25 09:17:11 RP2-13 kernel: [ 0.153087] CPU: All CPU(s) started in SVC mode.
Sep 25 09:17:11 RP2-13 kernel: [ 0.154074] devtmpfs: initialized
Sep 25 09:17:11 RP2-13 kernel: [ 0.178849] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
Sep 25 09:17:11 RP2-13 kernel: [ 0.180838] pinctrl core: initialized pinctrl subsystem
Sep 25 09:17:11 RP2-13 kernel: [ 0.183950] NET: Registered protocol family 16
Sep 25 09:17:11 RP2-13 kernel: [ 0.189569] DMA: preallocated 4096 KiB pool for atomic coherent allocations
Sep 25 09:17:11 RP2-13 kernel: [ 0.190740] bcm2709.uart_clock = 3000000
Sep 25 09:17:11 RP2-13 kernel: [ 0.193509] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
Sep 25 09:17:11 RP2-13 kernel: [ 0.193562] hw-breakpoint: maximum watchpoint size is 8 bytes.
Sep 25 09:17:11 RP2-13 kernel: [ 0.193617] mailbox: Broadcom VideoCore Mailbox driver
Sep 25 09:17:11 RP2-13 kernel: [ 0.193751] bcm2708_vcio: mailbox at f300b880
Sep 25 09:17:11 RP2-13 kernel: [ 0.194114] bcm_power: Broadcom power driver
Sep 25 09:17:11 RP2-13 kernel: [ 0.194151] bcm_power_open() -> 0
Sep 25 09:17:11 RP2-13 kernel: [ 0.194176] bcm_power_request(0, 8)
Sep 25 09:17:11 RP2-13 kernel: [ 0.694855] bcm_mailbox_read -> 00000080, 0
Sep 25 09:17:11 RP2-13 kernel: [ 0.694889] bcm_power_request -> 0
Sep 25 09:17:11 RP2-13 kernel: [ 0.695032] Serial: AMBA PL011 UART driver
Sep 25 09:17:11 RP2-13 kernel: [ 0.695179] dev:f1: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev3
Sep 25 09:17:11 RP2-13 kernel: [ 1.203459] console [ttyAMA0] enabled
Sep 25 09:17:11 RP2-13 kernel: [ 1.275742] SCSI subsystem initialized
Sep 25 09:17:11 RP2-13 kernel: [ 1.279763] usbcore: registered new interface driver usbfs
Sep 25 09:17:11 RP2-13 kernel: [ 1.285438] usbcore: registered new interface driver hub
Sep 25 09:17:11 RP2-13 kernel: [ 1.290908] usbcore: registered new device driver usb
Sep 25 09:17:11 RP2-13 kernel: [ 1.297815] Switched to clocksource arch_sys_counter
Sep 25 09:17:11 RP2-13 kernel: [ 1.333449] FS-Cache: Loaded
Sep 25 09:17:11 RP2-13 kernel: [ 1.336681] CacheFiles: Loaded
Sep 25 09:17:11 RP2-13 kernel: [ 1.351228] NET: Registered protocol family 2
Sep 25 09:17:11 RP2-13 kernel: [ 1.356872] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 1.364128] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 1.370829] TCP: Hash tables configured (established 8192 bind 8192)
Sep 25 09:17:11 RP2-13 kernel: [ 1.377299] TCP: reno registered
Sep 25 09:17:11 RP2-13 kernel: [ 1.380576] UDP hash table entries: 512 (order: 2, 16384 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 1.386562] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 1.393292] NET: Registered protocol family 1
Sep 25 09:17:11 RP2-13 kernel: [ 1.398355] RPC: Registered named UNIX socket transport module.
Sep 25 09:17:11 RP2-13 kernel: [ 1.404297] RPC: Registered udp transport module.
Sep 25 09:17:11 RP2-13 kernel: [ 1.409066] RPC: Registered tcp transport module.
Sep 25 09:17:11 RP2-13 kernel: [ 1.413785] RPC: Registered tcp NFSv4.1 backchannel transport module.
Sep 25 09:17:11 RP2-13 kernel: [ 1.421203] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Sep 25 09:17:11 RP2-13 kernel: [ 1.429618] bcm2708_dma: DMA manager at f3007000
Sep 25 09:17:11 RP2-13 kernel: [ 1.434411] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
Sep 25 09:17:11 RP2-13 kernel: [ 1.444225] futex hash table entries: 1024 (order: 4, 65536 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 1.450747] audit: initializing netlink subsys (disabled)
Sep 25 09:17:11 RP2-13 kernel: [ 1.456215] audit: type=2000 audit(1.239:1): initialized
Sep 25 09:17:11 RP2-13 kernel: [ 1.477887] VFS: Disk quotas dquot_6.5.2
Sep 25 09:17:11 RP2-13 kernel: [ 1.482202] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Sep 25 09:17:11 RP2-13 kernel: [ 1.491746] FS-Cache: Netfs 'nfs' registered for caching
Sep 25 09:17:11 RP2-13 kernel: [ 1.498174] NFS: Registering the id_resolver key type
Sep 25 09:17:11 RP2-13 kernel: [ 1.503303] Key type id_resolver registered
Sep 25 09:17:11 RP2-13 kernel: [ 1.507498] Key type id_legacy registered
Sep 25 09:17:11 RP2-13 kernel: [ 1.512694] msgmni has been set to 1853
Sep 25 09:17:11 RP2-13 kernel: [ 1.518415] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
Sep 25 09:17:11 RP2-13 kernel: [ 1.526016] io scheduler noop registered
Sep 25 09:17:11 RP2-13 kernel: [ 1.529995] io scheduler deadline registered (default)
Sep 25 09:17:11 RP2-13 kernel: [ 1.535463] io scheduler cfq registered
Sep 25 09:17:11 RP2-13 kernel: [ 1.541924] BCM2708FB: allocated DMA memory fac00000
Sep 25 09:17:11 RP2-13 kernel: [ 1.546937] BCM2708FB: allocated DMA channel 0 @ f3007000
Sep 25 09:17:11 RP2-13 kernel: [ 1.581714] Console: switching to colour frame buffer device 228x61
Sep 25 09:17:11 RP2-13 kernel: [ 1.606631] bcm2708-dmaengine bcm2708-dmaengine: Load BCM2835 DMA engine driver
Sep 25 09:17:11 RP2-13 kernel: [ 1.614411] uart-pl011 dev:f1: no DMA platform data
Sep 25 09:17:11 RP2-13 kernel: [ 1.619957] vc-cma: Videocore CMA driver
Sep 25 09:17:11 RP2-13 kernel: [ 1.623962] vc-cma: vc_cma_base = 0x00000000
Sep 25 09:17:11 RP2-13 kernel: [ 1.628823] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
Sep 25 09:17:11 RP2-13 kernel: [ 1.634324] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
Sep 25 09:17:11 RP2-13 kernel: [ 1.651651] brd: module loaded
Sep 25 09:17:11 RP2-13 kernel: [ 1.660503] loop: module loaded
Sep 25 09:17:11 RP2-13 kernel: [ 1.664059] vchiq: vchiq_init_state: slot_zero = 0xba800000, is_master = 0
Sep 25 09:17:11 RP2-13 kernel: [ 1.671987] Loading iSCSI transport class v2.0-870.
Sep 25 09:17:11 RP2-13 kernel: [ 1.678040] usbcore: registered new interface driver smsc95xx
Sep 25 09:17:11 RP2-13 kernel: [ 1.683971] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
Sep 25 09:17:11 RP2-13 kernel: [ 1.890189] Core Release: 2.80a
Sep 25 09:17:11 RP2-13 kernel: [ 1.893407] Setting default values for core params
Sep 25 09:17:11 RP2-13 kernel: [ 1.898360] Finished setting default values for core params
Sep 25 09:17:11 RP2-13 kernel: [ 2.104438] Using Buffer DMA mode
Sep 25 09:17:11 RP2-13 kernel: [ 2.107845] Periodic Transfer Interrupt Enhancement - disabled
Sep 25 09:17:11 RP2-13 kernel: [ 2.113783] Multiprocessor Interrupt Enhancement - disabled
Sep 25 09:17:11 RP2-13 kernel: [ 2.119477] OTG VER PARAM: 0, OTG VER FLAG: 0
Sep 25 09:17:11 RP2-13 kernel: [ 2.123921] Dedicated Tx FIFOs mode
Sep 25 09:17:11 RP2-13 kernel: [ 2.127874] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xbac14000 dma = 0xfac14000 len=9024
Sep 25 09:17:11 RP2-13 kernel: [ 2.137925] FIQ FSM acceleration enabled for :
Sep 25 09:17:11 RP2-13 kernel: [ 2.137925] Non-periodic Split Transactions
Sep 25 09:17:11 RP2-13 kernel: [ 2.137925] Periodic Split Transactions
Sep 25 09:17:11 RP2-13 kernel: [ 2.137925] High-Speed Isochronous Endpoints
Sep 25 09:17:11 RP2-13 kernel: [ 2.154936] dwc_otg: Microframe scheduler enabled
Sep 25 09:17:11 RP2-13 kernel: [ 2.155004] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x803d98b4
Sep 25 09:17:11 RP2-13 kernel: [ 2.165722] WARN::hcd_init_fiq:413: FIQ ASM at 0x803d9c10 length 36
Sep 25 09:17:11 RP2-13 kernel: [ 2.176721] WARN::hcd_init_fiq:438: MPHI regs_base at 0xbb80a000
Sep 25 09:17:11 RP2-13 kernel: [ 2.187462] dwc_otg bcm2708_usb: DWC OTG Controller
Sep 25 09:17:11 RP2-13 kernel: [ 2.197098] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
Sep 25 09:17:11 RP2-13 kernel: [ 2.209134] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
Sep 25 09:17:11 RP2-13 kernel: [ 2.219465] Init: Port Power? op_state=1
Sep 25 09:17:11 RP2-13 kernel: [ 2.228166] Init: Power Port (0)
Sep 25 09:17:11 RP2-13 kernel: [ 2.236384] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Sep 25 09:17:11 RP2-13 kernel: [ 2.247939] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Sep 25 09:17:11 RP2-13 kernel: [ 2.259936] usb usb1: Product: DWC OTG Controller
Sep 25 09:17:11 RP2-13 kernel: [ 2.269347] usb usb1: Manufacturer: Linux 3.18.11-v7+ dwc_otg_hcd
Sep 25 09:17:11 RP2-13 kernel: [ 2.280121] usb usb1: SerialNumber: bcm2708_usb
Sep 25 09:17:11 RP2-13 kernel: [ 2.290186] hub 1-0:1.0: USB hub found
Sep 25 09:17:11 RP2-13 kernel: [ 2.298650] hub 1-0:1.0: 1 port detected
Sep 25 09:17:11 RP2-13 kernel: [ 2.307585] dwc_otg: FIQ enabled
Sep 25 09:17:11 RP2-13 kernel: [ 2.307599] dwc_otg: NAK holdoff enabled
Sep 25 09:17:11 RP2-13 kernel: [ 2.307610] dwc_otg: FIQ split-transaction FSM enabled
Sep 25 09:17:11 RP2-13 kernel: [ 2.307650] Module dwc_common_port init
Sep 25 09:17:11 RP2-13 kernel: [ 2.308096] usbcore: registered new interface driver usb-storage
Sep 25 09:17:11 RP2-13 kernel: [ 2.319087] mousedev: PS/2 mouse device common for all mice
Sep 25 09:17:11 RP2-13 kernel: [ 2.329966] bcm2835-cpufreq: min=600000 max=900000
Sep 25 09:17:11 RP2-13 kernel: [ 2.339735] sdhci: Secure Digital Host Controller Interface driver
Sep 25 09:17:11 RP2-13 kernel: [ 2.350532] sdhci: Copyright(c) Pierre Ossman
Sep 25 09:17:11 RP2-13 kernel: [ 2.359713] DMA channels allocated for the MMC driver
Sep 25 09:17:11 RP2-13 kernel: [ 2.397859] Load BCM2835 MMC driver
Sep 25 09:17:11 RP2-13 kernel: [ 2.412872] sdhci-pltfm: SDHCI platform and OF driver helper
Sep 25 09:17:11 RP2-13 kernel: [ 2.423821] ledtrig-cpu: registered to indicate activity on CPUs
Sep 25 09:17:11 RP2-13 kernel: [ 2.434688] hidraw: raw HID events driver (C) Jiri Kosina
Sep 25 09:17:11 RP2-13 kernel: [ 2.446052] usbcore: registered new interface driver usbhid
Sep 25 09:17:11 RP2-13 kernel: [ 2.458342] usbhid: USB HID core driver
Sep 25 09:17:11 RP2-13 kernel: [ 2.469163] TCP: cubic registered
Sep 25 09:17:11 RP2-13 kernel: [ 2.479171] Initializing XFRM netlink socket
Sep 25 09:17:11 RP2-13 kernel: [ 2.488156] NET: Registered protocol family 17
Sep 25 09:17:11 RP2-13 kernel: [ 2.497407] Key type dns_resolver registered
Sep 25 09:17:11 RP2-13 kernel: [ 2.506700] Registering SWP/SWPB emulation handler
Sep 25 09:17:11 RP2-13 kernel: [ 2.507945] Indeed it is in host mode hprt0 = 00021501
Sep 25 09:17:11 RP2-13 kernel: [ 2.526759] registered taskstats version 1
Sep 25 09:17:11 RP2-13 kernel: [ 2.535724] vc-sm: Videocore shared memory driver
Sep 25 09:17:11 RP2-13 kernel: [ 2.545061] [vc_sm_connected_init]: start
Sep 25 09:17:11 RP2-13 kernel: [ 2.554443] [vc_sm_connected_init]: end - returning 0
Sep 25 09:17:11 RP2-13 kernel: [ 2.565503] Waiting for root device /dev/mmcblk0p2...
Sep 25 09:17:11 RP2-13 kernel: [ 2.579992] mmc0: host does not support reading read-only switch, assuming write-enable
Sep 25 09:17:11 RP2-13 kernel: [ 2.598879] mmc0: new high speed SDHC card at address aaaa
Sep 25 09:17:11 RP2-13 kernel: [ 2.609850] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
Sep 25 09:17:11 RP2-13 kernel: [ 2.625102] mmcblk0: p1 p2
Sep 25 09:17:11 RP2-13 kernel: [ 2.683721] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
Sep 25 09:17:11 RP2-13 kernel: [ 2.687937] usb 1-1: new high-speed USB device number 2 using dwc_otg
Sep 25 09:17:11 RP2-13 kernel: [ 2.695911] Indeed it is in host mode hprt0 = 00001101
Sep 25 09:17:11 RP2-13 kernel: [ 2.716887] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
Sep 25 09:17:11 RP2-13 kernel: [ 2.888263] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
Sep 25 09:17:11 RP2-13 kernel: [ 2.899837] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Sep 25 09:17:11 RP2-13 kernel: [ 2.912641] hub 1-1:1.0: USB hub found
Sep 25 09:17:11 RP2-13 kernel: [ 2.921352] hub 1-1:1.0: 5 ports detected
Sep 25 09:17:11 RP2-13 kernel: [ 3.086109] EXT4-fs (mmcblk0p2): orphan cleanup on readonly fs
Sep 25 09:17:11 RP2-13 kernel: [ 3.110151] EXT4-fs (mmcblk0p2): 1 orphan inode deleted
Sep 25 09:17:11 RP2-13 kernel: [ 3.120061] EXT4-fs (mmcblk0p2): recovery complete
Sep 25 09:17:11 RP2-13 kernel: [ 3.146811] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
Sep 25 09:17:11 RP2-13 kernel: [ 3.159714] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
Sep 25 09:17:11 RP2-13 kernel: [ 3.175567] devtmpfs: mounted
Sep 25 09:17:11 RP2-13 kernel: [ 3.183877] Freeing unused kernel memory: 384K (80754000 - 807b4000)
Sep 25 09:17:11 RP2-13 kernel: [ 3.228014] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
Sep 25 09:17:11 RP2-13 kernel: [ 3.338338] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
Sep 25 09:17:11 RP2-13 kernel: [ 3.350164] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Sep 25 09:17:11 RP2-13 kernel: [ 3.365253] smsc95xx v1.0.4
Sep 25 09:17:11 RP2-13 kernel: [ 3.432029] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:ad:5f:b2
Sep 25 09:17:11 RP2-13 kernel: [ 3.528023] usb 1-1.2: new low-speed USB device number 4 using dwc_otg
Sep 25 09:17:11 RP2-13 kernel: [ 3.681870] usb 1-1.2: New USB device found, idVendor=413c, idProduct=2107
Sep 25 09:17:11 RP2-13 kernel: [ 3.694287] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Sep 25 09:17:11 RP2-13 kernel: [ 3.694300] usb 1-1.2: Product: Dell USB Entry Keyboard
Sep 25 09:17:11 RP2-13 kernel: [ 3.694309] usb 1-1.2: Manufacturer: Dell
Sep 25 09:17:11 RP2-13 kernel: [ 3.727381] input: Dell Dell USB Entry Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-1.2/1-1.2:1.0/0003:413C:2107.0001/input/input0
Sep 25 09:17:11 RP2-13 kernel: [ 3.745652] hid-generic 0003:413C:2107.0001: input,hidraw0: USB HID v1.10 Keyboard [Dell Dell USB Entry Keyboard] on usb-bcm2708_usb-1.2/input0
Sep 25 09:17:11 RP2-13 kernel: [ 3.848150] usb 1-1.3: new low-speed USB device number 5 using dwc_otg
Sep 25 09:17:11 RP2-13 kernel: [ 3.963099] usb 1-1.3: New USB device found, idVendor=046d, idProduct=c077
Sep 25 09:17:11 RP2-13 kernel: [ 3.976828] usb 1-1.3: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Sep 25 09:17:11 RP2-13 kernel: [ 3.989977] usb 1-1.3: Product: USB Optical Mouse
Sep 25 09:17:11 RP2-13 kernel: [ 4.000759] usb 1-1.3: Manufacturer: Logitech
Sep 25 09:17:11 RP2-13 kernel: [ 4.017161] input: Logitech USB Optical Mouse as /devices/platform/bcm2708_usb/usb1/1-1/1-1.3/1-1.3:1.0/0003:046D:C077.0002/input/input1
Sep 25 09:17:11 RP2-13 kernel: [ 4.037330] hid-generic 0003:046D:C077.0002: input,hidraw1: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-bcm2708_usb-1.3/input0
Sep 25 09:17:11 RP2-13 kernel: [ 5.477869] random: nonblocking pool is initialized
Sep 25 09:17:11 RP2-13 kernel: [ 7.364900] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Sep 25 09:17:11 RP2-13 kernel: [ 7.646199] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Sep 25 09:17:11 RP2-13 kernel: [ 12.720825] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Sep 25 09:17:11 RP2-13 kernel: [ 14.325448] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
Sep 25 09:17:11 RP2-13 kernel: [ 16.695879] cfg80211: Calling CRDA to update world regulatory domain
Sep 25 09:17:12 RP2-13 kernel: [ 17.240682] Adding 102396k swap on /var/swap. Priority:-1 extents:2 across:2134012k SSFS
Sep 25 11:59:13 RP2-13 kernel: [ 9738.044001] usb 1-1.4: new high-speed USB device number 6 using dwc_otg
Sep 25 11:59:13 RP2-13 kernel: [ 9738.146503] usb 1-1.4: New USB device found, idVendor=05dc, idProduct=a81d
Sep 25 11:59:13 RP2-13 kernel: [ 9738.146532] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
Sep 25 11:59:13 RP2-13 kernel: [ 9738.146550] usb 1-1.4: Product: USB Flash Drive
Sep 25 11:59:13 RP2-13 kernel: [ 9738.146566] usb 1-1.4: Manufacturer: Lexar
Sep 25 11:59:13 RP2-13 kernel: [ 9738.146583] usb 1-1.4: SerialNumber: AABZJC9AAWX0FE6U
Sep 25 11:59:13 RP2-13 kernel: [ 9738.147813] usb-storage 1-1.4:1.0: USB Mass Storage device detected
Sep 25 11:59:13 RP2-13 kernel: [ 9738.150183] scsi host0: usb-storage 1-1.4:1.0
Sep 25 11:59:14 RP2-13 kernel: [ 9739.808127] scsi 0:0:0:0: Direct-Access Lexar USB Flash Drive 1100 PQ: 0 ANSI: 4
Sep 25 11:59:14 RP2-13 kernel: [ 9739.809726] sd 0:0:0:0: [sda] 15659008 512-byte logical blocks: (8.01 GB/7.46 GiB)
Sep 25 11:59:14 RP2-13 kernel: [ 9739.810368] sd 0:0:0:0: [sda] Write Protect is off
Sep 25 11:59:14 RP2-13 kernel: [ 9739.810398] sd 0:0:0:0: [sda] Mode Sense: 43 00 00 00
Sep 25 11:59:14 RP2-13 kernel: [ 9739.810988] sd 0:0:0:0: [sda] No Caching mode page found
Sep 25 11:59:14 RP2-13 kernel: [ 9739.811007] sd 0:0:0:0: [sda] Assuming drive cache: write through
Sep 25 11:59:14 RP2-13 kernel: [ 9739.815376] sda: sda1
Sep 25 11:59:14 RP2-13 kernel: [ 9739.818343] sd 0:0:0:0: [sda] Attached SCSI removable disk
Sep 25 11:59:14 RP2-13 kernel: [ 9739.835806] sd 0:0:0:0: Attached scsi generic sg0 type 0
Sep 25 11:59:15 RP2-13 kernel: [ 9740.295578] FAT-fs (sda1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
Sep 25 11:59:45 RP2-13 kernel: [ 9770.585959] usb 1-1.4: USB disconnect, device number 6
Sep 25 16:17:11 RP2-13 kernel: imklog 5.8.11, log source = /proc/kmsg started.
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Booting Linux on physical CPU 0xf00
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Initializing cgroup subsys cpu
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Initializing cgroup subsys cpuacct
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Linux version 3.18.11-v7+ (dc4@dc4-XPS13-9333) (gcc version 4.8.3 20140303 (prerelease) (crosstool-NG linaro-1.13.1+bzr2650 - Linaro GCC 2014.03) ) #781 SMP PREEMPT Tue Apr 21 18:07:59 BST 2015
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Machine model: Raspberry Pi 2 Model B
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] cma: Reserved 8 MiB at 0x3a800000
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Memory policy: Data cache writealloc
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] On node 0 totalpages: 241664
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] free_area_init_node: node 0, pgdat 8080f480, node_mem_map ba093000
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Normal zone: 1888 pages used for memmap
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Normal zone: 0 pages reserved
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Normal zone: 241664 pages, LIFO batch:31
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] [bcm2709_smp_init_cpus] enter (8620->f3003010)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] [bcm2709_smp_init_cpus] ncores=4
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] PERCPU: Embedded 10 pages/cpu @ba061000 s11456 r8192 d21312 u40960
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] pcpu-alloc: s11456 r8192 d21312 u40960 alloc=10*4096
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 239776
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Kernel command line: dma.dmachans=0x7f35 bcm2708_fb.fbwidth=1824 bcm2708_fb.fbheight=984 bcm2709.boardrev=0xa01041 bcm2709.serial=0x55ad5fb2 smsc95xx.macaddr=B8:27:EB:AD:5F:B2 bcm2708_fb.fbswap=1 bcm2709.disk_led_gpio=47 bcm2709.disk_led_active_low=0 sdhci-bcm2708.emmc_clock_freq=250000000 vc_mem.mem_base=0x3dc00000 vc_mem.mem_size=0x3f000000 dwc_otg.lpm_enable=0 console=ttyAMA0,115200 console=tty1 root=/dev/mmcblk0p2 rootfstype=ext4 elevator=deadline rootwait
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] PID hash table entries: 4096 (order: 2, 16384 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Memory: 940832K/966656K available (5722K kernel code, 397K rwdata, 1748K rodata, 384K init, 763K bss, 25824K reserved)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Virtual kernel memory layout:
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] fixmap : 0xffc00000 - 0xffe00000 (2048 kB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] vmalloc : 0xbb800000 - 0xff000000 (1080 MB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] lowmem : 0x80000000 - 0xbb000000 ( 944 MB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] modules : 0x7f000000 - 0x80000000 ( 16 MB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] .text : 0x80008000 - 0x80753a48 (7471 kB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] .init : 0x80754000 - 0x807b4000 ( 384 kB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] .data : 0x807b4000 - 0x808174bc ( 398 kB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] .bss : 0x808174bc - 0x808d6254 ( 764 kB)
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Preemptible hierarchical RCU implementation.
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] NR_IRQS:608
Sep 25 16:17:11 RP2-13 kernel: [ 0.000000] Architected cp15 timer(s) running at 19.20MHz (virt).
Sep 25 16:17:11 RP2-13 kernel: [ 0.000015] sched_clock: 56 bits at 19MHz, resolution 52ns, wraps every 3579139424256ns
Sep 25 16:17:11 RP2-13 kernel: [ 0.000037] Switching to timer-based delay loop, resolution 52ns
Sep 25 16:17:11 RP2-13 kernel: [ 0.000333] Console: colour dummy device 80x30
Sep 25 16:17:11 RP2-13 kernel: [ 0.001758] console [tty1] enabled
Sep 25 16:17:11 RP2-13 kernel: [ 0.001809] Calibrating delay loop (skipped), value calculated using timer frequency.. 38.40 BogoMIPS (lpj=192000)
Sep 25 16:17:11 RP2-13 kernel: [ 0.001892] pid_max: default: 32768 minimum: 301
Sep 25 16:17:11 RP2-13 kernel: [ 0.002297] Mount-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 0.002357] Mountpoint-cache hash table entries: 2048 (order: 1, 8192 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 0.003630] Initializing cgroup subsys memory
Sep 25 16:17:11 RP2-13 kernel: [ 0.003720] Initializing cgroup subsys devices
Sep 25 16:17:11 RP2-13 kernel: [ 0.003773] Initializing cgroup subsys freezer
Sep 25 16:17:11 RP2-13 kernel: [ 0.003824] Initializing cgroup subsys net_cls
Sep 25 16:17:11 RP2-13 kernel: [ 0.003889] Initializing cgroup subsys blkio
Sep 25 16:17:11 RP2-13 kernel: [ 0.003994] CPU: Testing write buffer coherency: ok
Sep 25 16:17:11 RP2-13 kernel: [ 0.004111] ftrace: allocating 19614 entries in 58 pages
Sep 25 16:17:11 RP2-13 kernel: [ 0.052642] CPU0: update cpu_capacity 1024
Sep 25 16:17:11 RP2-13 kernel: [ 0.052722] CPU0: thread -1, cpu 0, socket 15, mpidr 80000f00
Sep 25 16:17:11 RP2-13 kernel: [ 0.052762] [bcm2709_smp_prepare_cpus] enter
Sep 25 16:17:11 RP2-13 kernel: [ 0.052917] Setting up static identity map for 0x528478 - 0x5284ac
Sep 25 16:17:11 RP2-13 kernel: [ 0.112540] [bcm2709_boot_secondary] cpu:1 started (0) 17
Sep 25 16:17:11 RP2-13 kernel: [ 0.112844] CPU1: Booted secondary processor
Sep 25 16:17:11 RP2-13 kernel: [ 0.112852] [bcm2709_secondary_init] enter cpu:1
Sep 25 16:17:11 RP2-13 kernel: [ 0.112905] CPU1: update cpu_capacity 1024
Sep 25 16:17:11 RP2-13 kernel: [ 0.112914] CPU1: thread -1, cpu 1, socket 15, mpidr 80000f01
Sep 25 16:17:11 RP2-13 kernel: [ 0.132514] [bcm2709_boot_secondary] cpu:2 started (0) 18
Sep 25 16:17:11 RP2-13 kernel: [ 0.132771] CPU2: Booted secondary processor
Sep 25 16:17:11 RP2-13 kernel: [ 0.132778] [bcm2709_secondary_init] enter cpu:2
Sep 25 16:17:11 RP2-13 kernel: [ 0.132808] CPU2: update cpu_capacity 1024
Sep 25 16:17:11 RP2-13 kernel: [ 0.132817] CPU2: thread -1, cpu 2, socket 15, mpidr 80000f02
Sep 25 16:17:11 RP2-13 kernel: [ 0.152587] [bcm2709_boot_secondary] cpu:3 started (0) 18
Sep 25 16:17:11 RP2-13 kernel: [ 0.152827] CPU3: Booted secondary processor
Sep 25 16:17:11 RP2-13 kernel: [ 0.152834] [bcm2709_secondary_init] enter cpu:3
Sep 25 16:17:11 RP2-13 kernel: [ 0.152865] CPU3: update cpu_capacity 1024
Sep 25 16:17:11 RP2-13 kernel: [ 0.152873] CPU3: thread -1, cpu 3, socket 15, mpidr 80000f03
Sep 25 16:17:11 RP2-13 kernel: [ 0.152967] Brought up 4 CPUs
Sep 25 16:17:11 RP2-13 kernel: [ 0.153087] SMP: Total of 4 processors activated (153.60 BogoMIPS).
Sep 25 16:17:11 RP2-13 kernel: [ 0.153120] CPU: All CPU(s) started in SVC mode.
Sep 25 16:17:11 RP2-13 kernel: [ 0.154099] devtmpfs: initialized
Sep 25 16:17:11 RP2-13 kernel: [ 0.178895] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5
Sep 25 16:17:11 RP2-13 kernel: [ 0.180888] pinctrl core: initialized pinctrl subsystem
Sep 25 16:17:11 RP2-13 kernel: [ 0.183997] NET: Registered protocol family 16
Sep 25 16:17:11 RP2-13 kernel: [ 0.189623] DMA: preallocated 4096 KiB pool for atomic coherent allocations
Sep 25 16:17:11 RP2-13 kernel: [ 0.190796] bcm2709.uart_clock = 3000000
Sep 25 16:17:11 RP2-13 kernel: [ 0.193568] hw-breakpoint: found 5 (+1 reserved) breakpoint and 4 watchpoint registers.
Sep 25 16:17:11 RP2-13 kernel: [ 0.193621] hw-breakpoint: maximum watchpoint size is 8 bytes.
Sep 25 16:17:11 RP2-13 kernel: [ 0.193676] mailbox: Broadcom VideoCore Mailbox driver
Sep 25 16:17:11 RP2-13 kernel: [ 0.193807] bcm2708_vcio: mailbox at f300b880
Sep 25 16:17:11 RP2-13 kernel: [ 0.194164] bcm_power: Broadcom power driver
Sep 25 16:17:11 RP2-13 kernel: [ 0.194202] bcm_power_open() -> 0
Sep 25 16:17:11 RP2-13 kernel: [ 0.194227] bcm_power_request(0, 8)
Sep 25 16:17:11 RP2-13 kernel: [ 0.694907] bcm_mailbox_read -> 00000080, 0
Sep 25 16:17:11 RP2-13 kernel: [ 0.694939] bcm_power_request -> 0
Sep 25 16:17:11 RP2-13 kernel: [ 0.695081] Serial: AMBA PL011 UART driver
Sep 25 16:17:11 RP2-13 kernel: [ 0.695232] dev:f1: ttyAMA0 at MMIO 0x3f201000 (irq = 83, base_baud = 0) is a PL011 rev3
Sep 25 16:17:11 RP2-13 kernel: [ 1.203512] console [ttyAMA0] enabled
Sep 25 16:17:11 RP2-13 kernel: [ 1.285757] SCSI subsystem initialized
Sep 25 16:17:11 RP2-13 kernel: [ 1.289776] usbcore: registered new interface driver usbfs
Sep 25 16:17:11 RP2-13 kernel: [ 1.295447] usbcore: registered new interface driver hub
Sep 25 16:17:11 RP2-13 kernel: [ 1.300915] usbcore: registered new device driver usb
Sep 25 16:17:11 RP2-13 kernel: [ 1.307820] Switched to clocksource arch_sys_counter
Sep 25 16:17:11 RP2-13 kernel: [ 1.343449] FS-Cache: Loaded
Sep 25 16:17:11 RP2-13 kernel: [ 1.346677] CacheFiles: Loaded
Sep 25 16:17:11 RP2-13 kernel: [ 1.361248] NET: Registered protocol family 2
Sep 25 16:17:11 RP2-13 kernel: [ 1.366905] TCP established hash table entries: 8192 (order: 3, 32768 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 1.374158] TCP bind hash table entries: 8192 (order: 4, 65536 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 1.380861] TCP: Hash tables configured (established 8192 bind 8192)
Sep 25 16:17:11 RP2-13 kernel: [ 1.387331] TCP: reno registered
Sep 25 16:17:11 RP2-13 kernel: [ 1.390608] UDP hash table entries: 512 (order: 2, 16384 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 1.396593] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 1.403316] NET: Registered protocol family 1
Sep 25 16:17:11 RP2-13 kernel: [ 1.408369] RPC: Registered named UNIX socket transport module.
Sep 25 16:17:11 RP2-13 kernel: [ 1.414313] RPC: Registered udp transport module.
Sep 25 16:17:11 RP2-13 kernel: [ 1.419086] RPC: Registered tcp transport module.
Sep 25 16:17:11 RP2-13 kernel: [ 1.423805] RPC: Registered tcp NFSv4.1 backchannel transport module.
Sep 25 16:17:11 RP2-13 kernel: [ 1.431230] hw perfevents: enabled with armv7_cortex_a7 PMU driver, 5 counters available
Sep 25 16:17:11 RP2-13 kernel: [ 1.439646] bcm2708_dma: DMA manager at f3007000
Sep 25 16:17:11 RP2-13 kernel: [ 1.444444] vc-mem: phys_addr:0x00000000 mem_base=0x3dc00000 mem_size:0x3f000000(1008 MiB)
Sep 25 16:17:11 RP2-13 kernel: [ 1.454261] futex hash table entries: 1024 (order: 4, 65536 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 1.460785] audit: initializing netlink subsys (disabled)
Sep 25 16:17:11 RP2-13 kernel: [ 1.466257] audit: type=2000 audit(1.249:1): initialized
Sep 25 16:17:11 RP2-13 kernel: [ 1.487864] VFS: Disk quotas dquot_6.5.2
Sep 25 16:17:11 RP2-13 kernel: [ 1.492172] Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Sep 25 16:17:11 RP2-13 kernel: [ 1.501719] FS-Cache: Netfs 'nfs' registered for caching
Sep 25 16:17:11 RP2-13 kernel: [ 1.508141] NFS: Registering the id_resolver key type
Sep 25 16:17:11 RP2-13 kernel: [ 1.513279] Key type id_resolver registered
Sep 25 16:17:11 RP2-13 kernel: [ 1.517474] Key type id_legacy registered
Sep 25 16:17:11 RP2-13 kernel: [ 1.522673] msgmni has been set to 1853
Sep 25 16:17:11 RP2-13 kernel: [ 1.528427] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
Sep 25 16:17:11 RP2-13 kernel: [ 1.536030] io scheduler noop registered
Sep 25 16:17:11 RP2-13 kernel: [ 1.540009] io scheduler deadline registered (default)
Sep 25 16:17:11 RP2-13 kernel: [ 1.545474] io scheduler cfq registered
Sep 25 16:17:11 RP2-13 kernel: [ 1.551930] BCM2708FB: allocated DMA memory fac00000
Sep 25 16:17:11 RP2-13 kernel: [ 1.556943] BCM2708FB: allocated DMA channel 0 @ f3007000
Sep 25 16:17:11 RP2-13 kernel: [ 1.591734] Console: switching to colour frame buffer device 228x61
Sep 25 16:17:11 RP2-13 kernel: [ 1.616634] bcm2708-dmaengine bcm2708-dmaengine: Load BCM2835 DMA engine driver
Sep 25 16:17:11 RP2-13 kernel: [ 1.624399] uart-pl011 dev:f1: no DMA platform data
Sep 25 16:17:11 RP2-13 kernel: [ 1.629943] vc-cma: Videocore CMA driver
Sep 25 16:17:11 RP2-13 kernel: [ 1.633950] vc-cma: vc_cma_base = 0x00000000
Sep 25 16:17:11 RP2-13 kernel: [ 1.638811] vc-cma: vc_cma_size = 0x00000000 (0 MiB)
Sep 25 16:17:11 RP2-13 kernel: [ 1.644312] vc-cma: vc_cma_initial = 0x00000000 (0 MiB)
Sep 25 16:17:11 RP2-13 kernel: [ 1.661646] brd: module loaded
Sep 25 16:17:11 RP2-13 kernel: [ 1.670517] loop: module loaded
Sep 25 16:17:11 RP2-13 kernel: [ 1.674059] vchiq: vchiq_init_state: slot_zero = 0xba800000, is_master = 0
Sep 25 16:17:11 RP2-13 kernel: [ 1.681979] Loading iSCSI transport class v2.0-870.
Sep 25 16:17:11 RP2-13 kernel: [ 1.688024] usbcore: registered new interface driver smsc95xx
Sep 25 16:17:11 RP2-13 kernel: [ 1.693951] dwc_otg: version 3.00a 10-AUG-2012 (platform bus)
Sep 25 16:17:11 RP2-13 kernel: [ 1.900190] Core Release: 2.80a
Sep 25 16:17:11 RP2-13 kernel: [ 1.903407] Setting default values for core params
Sep 25 16:17:11 RP2-13 kernel: [ 1.908357] Finished setting default values for core params
Sep 25 16:17:11 RP2-13 kernel: [ 2.114434] Using Buffer DMA mode
Sep 25 16:17:11 RP2-13 kernel: [ 2.117843] Periodic Transfer Interrupt Enhancement - disabled
Sep 25 16:17:11 RP2-13 kernel: [ 2.123780] Multiprocessor Interrupt Enhancement - disabled
Sep 25 16:17:11 RP2-13 kernel: [ 2.129474] OTG VER PARAM: 0, OTG VER FLAG: 0
Sep 25 16:17:11 RP2-13 kernel: [ 2.133918] Dedicated Tx FIFOs mode
Sep 25 16:17:11 RP2-13 kernel: [ 2.137877] WARN::dwc_otg_hcd_init:1047: FIQ DMA bounce buffers: virt = 0xbac14000 dma = 0xfac14000 len=9024
Sep 25 16:17:11 RP2-13 kernel: [ 2.147929] FIQ FSM acceleration enabled for :
Sep 25 16:17:11 RP2-13 kernel: [ 2.147929] Non-periodic Split Transactions
Sep 25 16:17:11 RP2-13 kernel: [ 2.147929] Periodic Split Transactions
Sep 25 16:17:11 RP2-13 kernel: [ 2.147929] High-Speed Isochronous Endpoints
Sep 25 16:17:11 RP2-13 kernel: [ 2.164924] dwc_otg: Microframe scheduler enabled
Sep 25 16:17:11 RP2-13 kernel: [ 2.164990] WARN::hcd_init_fiq:412: FIQ on core 1 at 0x803d98b4
Sep 25 16:17:11 RP2-13 kernel: [ 2.175713] WARN::hcd_init_fiq:413: FIQ ASM at 0x803d9c10 length 36
Sep 25 16:17:11 RP2-13 kernel: [ 2.186706] WARN::hcd_init_fiq:438: MPHI regs_base at 0xbb80a000
Sep 25 16:17:11 RP2-13 kernel: [ 2.197440] dwc_otg bcm2708_usb: DWC OTG Controller
Sep 25 16:17:11 RP2-13 kernel: [ 2.207077] dwc_otg bcm2708_usb: new USB bus registered, assigned bus number 1
Sep 25 16:17:11 RP2-13 kernel: [ 2.219112] dwc_otg bcm2708_usb: irq 32, io mem 0x00000000
Sep 25 16:17:11 RP2-13 kernel: [ 2.229433] Init: Port Power? op_state=1
Sep 25 16:17:11 RP2-13 kernel: [ 2.238134] Init: Power Port (0)
Sep 25 16:17:11 RP2-13 kernel: [ 2.246342] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
Sep 25 16:17:11 RP2-13 kernel: [ 2.257905] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
Sep 25 16:17:11 RP2-13 kernel: [ 2.269895] usb usb1: Product: DWC OTG Controller
Sep 25 16:17:11 RP2-13 kernel: [ 2.279301] usb usb1: Manufacturer: Linux 3.18.11-v7+ dwc_otg_hcd
Sep 25 16:17:11 RP2-13 kernel: [ 2.290079] usb usb1: SerialNumber: bcm2708_usb
Sep 25 16:17:11 RP2-13 kernel: [ 2.300169] hub 1-0:1.0: USB hub found
Sep 25 16:17:11 RP2-13 kernel: [ 2.308625] hub 1-0:1.0: 1 port detected
Sep 25 16:17:11 RP2-13 kernel: [ 2.317567] dwc_otg: FIQ enabled
Sep 25 16:17:11 RP2-13 kernel: [ 2.317581] dwc_otg: NAK holdoff enabled
Sep 25 16:17:11 RP2-13 kernel: [ 2.317593] dwc_otg: FIQ split-transaction FSM enabled
Sep 25 16:17:11 RP2-13 kernel: [ 2.317633] Module dwc_common_port init
Sep 25 16:17:11 RP2-13 kernel: [ 2.318104] usbcore: registered new interface driver usb-storage
Sep 25 16:17:11 RP2-13 kernel: [ 2.329078] mousedev: PS/2 mouse device common for all mice
Sep 25 16:17:11 RP2-13 kernel: [ 2.339888] bcm2835-cpufreq: min=600000 max=900000
Sep 25 16:17:11 RP2-13 kernel: [ 2.349682] sdhci: Secure Digital Host Controller Interface driver
Sep 25 16:17:11 RP2-13 kernel: [ 2.360471] sdhci: Copyright(c) Pierre Ossman
Sep 25 16:17:11 RP2-13 kernel: [ 2.369656] DMA channels allocated for the MMC driver
Sep 25 16:17:11 RP2-13 kernel: [ 2.407864] Load BCM2835 MMC driver
Sep 25 16:17:11 RP2-13 kernel: [ 2.421875] sdhci-pltfm: SDHCI platform and OF driver helper
Sep 25 16:17:11 RP2-13 kernel: [ 2.432837] ledtrig-cpu: registered to indicate activity on CPUs
Sep 25 16:17:11 RP2-13 kernel: [ 2.443701] hidraw: raw HID events driver (C) Jiri Kosina
Sep 25 16:17:11 RP2-13 kernel: [ 2.456075] usbcore: registered new interface driver usbhid
Sep 25 16:17:11 RP2-13 kernel: [ 2.466347] usbhid: USB HID core driver
Sep 25 16:17:11 RP2-13 kernel: [ 2.476166] TCP: cubic registered
Sep 25 16:17:11 RP2-13 kernel: [ 2.486167] Initializing XFRM netlink socket
Sep 25 16:17:11 RP2-13 kernel: [ 2.495143] NET: Registered protocol family 17
Sep 25 16:17:11 RP2-13 kernel: [ 2.504409] Key type dns_resolver registered
Sep 25 16:17:11 RP2-13 kernel: [ 2.513712] Registering SWP/SWPB emulation handler
Sep 25 16:17:11 RP2-13 kernel: [ 2.517964] Indeed it is in host mode hprt0 = 00021501
Sep 25 16:17:11 RP2-13 kernel: [ 2.533788] registered taskstats version 1
Sep 25 16:17:11 RP2-13 kernel: [ 2.542736] vc-sm: Videocore shared memory driver
Sep 25 16:17:11 RP2-13 kernel: [ 2.552078] [vc_sm_connected_init]: start
Sep 25 16:17:11 RP2-13 kernel: [ 2.561431] [vc_sm_connected_init]: end - returning 0
Sep 25 16:17:11 RP2-13 kernel: [ 2.572484] Waiting for root device /dev/mmcblk0p2...
Sep 25 16:17:11 RP2-13 kernel: [ 2.587165] mmc0: host does not support reading read-only switch, assuming write-enable
Sep 25 16:17:11 RP2-13 kernel: [ 2.605776] mmc0: new high speed SDHC card at address aaaa
Sep 25 16:17:11 RP2-13 kernel: [ 2.616754] mmcblk0: mmc0:aaaa SL16G 14.8 GiB
Sep 25 16:17:11 RP2-13 kernel: [ 2.631727] mmcblk0: p1 p2
Sep 25 16:17:11 RP2-13 kernel: [ 2.694021] EXT4-fs (mmcblk0p2): INFO: recovery required on readonly filesystem
Sep 25 16:17:11 RP2-13 kernel: [ 2.697936] usb 1-1: new high-speed USB device number 2 using dwc_otg
Sep 25 16:17:11 RP2-13 kernel: [ 2.706204] Indeed it is in host mode hprt0 = 00001101
Sep 25 16:17:11 RP2-13 kernel: [ 2.727176] EXT4-fs (mmcblk0p2): write access will be enabled during recovery
Sep 25 16:17:11 RP2-13 kernel: [ 2.814936] EXT4-fs (mmcblk0p2): orphan cleanup on readonly fs
Sep 25 16:17:11 RP2-13 kernel: [ 2.840095] EXT4-fs (mmcblk0p2): 3 orphan inodes deleted
Sep 25 16:17:11 RP2-13 kernel: [ 2.850249] EXT4-fs (mmcblk0p2): recovery complete
Sep 25 16:17:11 RP2-13 kernel: [ 2.883687] EXT4-fs (mmcblk0p2): mounted filesystem with ordered data mode. Opts: (null)
Sep 25 16:17:11 RP2-13 kernel: [ 2.896643] VFS: Mounted root (ext4 filesystem) readonly on device 179:2.
Sep 25 16:17:11 RP2-13 kernel: [ 2.908469] usb 1-1: New USB device found, idVendor=0424, idProduct=9514
Sep 25 16:17:11 RP2-13 kernel: [ 2.912930] devtmpfs: mounted
Sep 25 16:17:11 RP2-13 kernel: [ 2.913723] Freeing unused kernel memory: 384K (80754000 - 807b4000)
Sep 25 16:17:11 RP2-13 kernel: [ 2.938720] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Sep 25 16:17:11 RP2-13 kernel: [ 2.951647] hub 1-1:1.0: USB hub found
Sep 25 16:17:11 RP2-13 kernel: [ 2.960443] hub 1-1:1.0: 5 ports detected
Sep 25 16:17:11 RP2-13 kernel: [ 3.248078] usb 1-1.1: new high-speed USB device number 3 using dwc_otg
Sep 25 16:17:11 RP2-13 kernel: [ 3.358534] usb 1-1.1: New USB device found, idVendor=0424, idProduct=ec00
Sep 25 16:17:11 RP2-13 kernel: [ 3.370433] usb 1-1.1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
Sep 25 16:17:11 RP2-13 kernel: [ 3.386250] smsc95xx v1.0.4
Sep 25 16:17:11 RP2-13 kernel: [ 3.452960] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:ad:5f:b2
Sep 25 16:17:11 RP2-13 kernel: [ 3.548122] usb 1-1.4: new low-speed USB device number 4 using dwc_otg
Sep 25 16:17:11 RP2-13 kernel: [ 3.664267] usb 1-1.4: New USB device found, idVendor=046d, idProduct=c077
Sep 25 16:17:11 RP2-13 kernel: [ 3.677694] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Sep 25 16:17:11 RP2-13 kernel: [ 3.691296] usb 1-1.4: Product: USB Optical Mouse
Sep 25 16:17:11 RP2-13 kernel: [ 3.701825] usb 1-1.4: Manufacturer: Logitech
Sep 25 16:17:11 RP2-13 kernel: [ 3.719636] input: Logitech USB Optical Mouse as /devices/platform/bcm2708_usb/usb1/1-1/1-1.4/1-1.4:1.0/0003:046D:C077.0001/input/input0
Sep 25 16:17:11 RP2-13 kernel: [ 3.738747] hid-generic 0003:046D:C077.0001: input,hidraw0: USB HID v1.11 Mouse [Logitech USB Optical Mouse] on usb-bcm2708_usb-1.4/input0
Sep 25 16:17:11 RP2-13 kernel: [ 3.838168] usb 1-1.5: new low-speed USB device number 5 using dwc_otg
Sep 25 16:17:11 RP2-13 kernel: [ 3.993527] usb 1-1.5: New USB device found, idVendor=413c, idProduct=2107
Sep 25 16:17:11 RP2-13 kernel: [ 4.007598] usb 1-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=0
Sep 25 16:17:11 RP2-13 kernel: [ 4.021686] usb 1-1.5: Product: Dell USB Entry Keyboard
Sep 25 16:17:11 RP2-13 kernel: [ 4.033201] usb 1-1.5: Manufacturer: Dell
Sep 25 16:17:11 RP2-13 kernel: [ 4.069920] input: Dell Dell USB Entry Keyboard as /devices/platform/bcm2708_usb/usb1/1-1/1-1.5/1-1.5:1.0/0003:413C:2107.0002/input/input1
Sep 25 16:17:11 RP2-13 kernel: [ 4.088657] hid-generic 0003:413C:2107.0002: input,hidraw1: USB HID v1.10 Keyboard [Dell Dell USB Entry Keyboard] on usb-bcm2708_usb-1.5/input0
Sep 25 16:17:11 RP2-13 kernel: [ 6.505126] random: nonblocking pool is initialized
Sep 25 16:17:11 RP2-13 kernel: [ 6.926389] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Sep 25 16:17:11 RP2-13 kernel: [ 7.205580] EXT4-fs (mmcblk0p2): re-mounted. Opts: (null)
Sep 25 16:17:11 RP2-13 kernel: [ 12.313134] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup
Sep 25 16:17:11 RP2-13 kernel: [ 13.853730] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x41E1
Sep 25 16:17:11 RP2-13 kernel: [ 16.314636] cfg80211: Calling CRDA to update world regulatory domain
Sep 25 16:17:12 RP2-13 kernel: [ 16.768675] Adding 102396k swap on /var/swap. Priority:-1 extents:2 across:2134012k SSFS
Reference in New Issue Copy Permalink